Show off a market row, a trade row or your whole hand. Snap Small, Medium and Large rails together for 1 to 6 cards, all leaning back at an easy-to-read 15 degrees. Game over? Roll the rails together and they snap into one locked brick, ready for the game box or your travel bag.
One continuous card slot, three rail lengths and clips built into every end. No loose parts.
Small holds 1 card, Medium holds 2, Large holds 3. Every rail has a dovetail tab on its right end and a pocket on its left, so any rail clips to any rail: Large, Large, Large or Large, Medium, Small. Five cards is a Medium plus a Large.
The slot runs the full length with no dividers, so mini, standard, square and tarot cards all fit. It is 3.4 mm wide for sleeved cards or a small stack, with a chamfered top so cards drop right in.
Cards lean back 15 degrees so the whole table can read them. A 54 mm deep foot and a low back wall keep the row planted when someone bumps the table.
Every rail doubles as half of a carry case. Roll the top rails over onto a base rail and they snap shut into a solid 54 x 26 mm bar that will not fall apart in a bag. Press "Pack for travel" on the viewer to watch it happen.
Unpacking is the same steps in reverse: pull the top rails firmly off the base, roll them slot side up, clip them into a row and drop in the cards.
PLA or PETG, 0.2 mm layers, 2 to 3 walls, 15% infill, no supports. Small and Medium fit an A1 mini. Large is 218 mm long with its tab and needs a 256 mm bed like the P1S, X1C or A1. Use 3 walls so the snap hooks are strong.
Print every rail flat side down, exactly as it loads. The slot leans at 15 degrees and the hooks are short ramps, so everything prints clean with no supports.
End clips have 0.2 mm clearance per side. Print a Small and a Medium first and test the clip and the travel snap. Clip tight: sand the tab sides lightly. Snap too stiff: file the small ramp on top of the back wall. Snap too loose: print with 4 walls.
| Rails | Small 70 mm (1 card), Medium 140 mm (2 cards), Large 210 mm (3 cards), plus an 8 mm clip tab on each |
|---|---|
| Footprint | 54 mm deep, 21 mm tall at the slot, 24.5 mm at the back wall |
| Card slot | 3.4 mm wide, 14 mm deep, 15 degree lean, 1 mm entry chamfer |
| Joints | Two built-in dovetail tabs on the right end, matching pockets on the left end |
| Packed | Rail length x 54 x 26 mm brick, snap-locked front and back |
| Hardware | None. No magnets, no glue, no print pauses |
Cards shown in the 3D preview are from Dune: Imperium and its expansions, for scale only. Dune: Imperium is published by Dire Wolf; card art belongs to its owners. Card images via dunecardshub.com. Denver Board Gamers is not affiliated with Dire Wolf or Legendary. The Ultimate Deck Viewer works with any card game.
Free tools we built because we could not stop tinkering, plus handmade gear from the workshop.
Print-ready gear for the table: a DCC snap kit, a fold-flat phone stand and a collapsible deck viewer.
Browse the models →Cube-drop battle randomizer for Dead Reckoning. See the odds before you fight.
Run a battle →Canvas, metal and acrylic prints, made to order in Centennial. 5.0 star rated.
Shop the goods →Princess Donut, Prepotente and the Desperado Club on canvas, metal and acrylic.
See the collection →Tokens, organizers and accessories printed to your spec. Resin and FDM.
Ask for a quote →Pick games from BoardGameGeek, let the group vote, track RSVPs. Free.
🚧 Under construction